| Keepsake Security Device - Generation 2 ... The ultimate male chastity security device! |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
New - Online instructions for the KSD-G2!
The Keepsake Security Device - Generation 2 (KSD-G2)was designed to
provide an additional level of security for the CB-2000, New Style CB-3000, and The
New Style Curve. It is made in 3 standard sizes for the following soft shaft sizes:
1-1/2", 1-3/8", and 1-1/4". The new design for the CB-2000 adds a ridge
around the outside of the sleeve that allows the KSD-G2 to snap into the
tube of the CB-2000 but it fits just a bit looser in the CB-3000 and Curve so as
not to split the cage apart.
All men are made a bit different. Because of the physical makeup of some men, they have found that it is possible to pull out
of the CB-2000, CB-3000, or The Curve, regardless of the configuration of rings and spacers that they use. In order to assist
the man in his desire to stay chaste for his Keyholder, and to give the Keyholder the peace of mind that she deserves, Kept
For Her designed and offers the KSD-G2.
Any man in chastity comes to points of frustration where he will do anything to get out of his CB. The KSD-G2 will aid in
preventing the man from pulling out of the tube and masturbating.
How the KSD-G2 Works
The KSD-G2 fits onto the locking pin and goes partway into the tube, while a part of it is on the outside of the tube. The
KSD-G2 works by adding constriction and friction to the male shaft, thus making attempts at pulling out difficult, if not
impossible. The inside diameter of the KSD-G2 is considerably smaller than the shaft size it was ordered for (see chart
on Measuring page). If indeed you are able to pull out, you will not get back in without your Keyholder finding out. You
will be in big trouble!!
The KSD-G2 will not cause fluid backup (unless you specify the
wrong size and that can be easily corrected!). Also, the KSD-G2
will not cause pain during arousals. It is very comfortable to wear
and to stay hygienically clean while locked up for long periods of
time.
The KSD-G2 is made out of UHMW plastic, which has the qualities
of being lightweight, resistant to any oils or lotions, and easy to
modify if necessary. Each KSD-G2 is manufactured by plastic
injection molding. This process assures you of consistent quality and
exacting tolerances from one unit to the next.
What is the difference between the KSD-G2 for the CB-2000 and
the one for the CB-3000/Curve? The KSD-G2 fits 3/8" into the
chastity tube of the 2000/3000/Curve. The opening of the CB-3000
and The Curve is the same so the same KSD-G2 fits both. The opening of the CB-2000 is larger. So a different KSD-G2 had
to be designed to fit snugly into the CB-2000. The KSD-G2 snaps into the CB-2000 tube but has just a bit looser fit in the tube
of the 3000 and Curve so that it does not split the cage apart.
provide an additional level of security for the CB-2000, New Style CB-3000, and The
New Style Curve. It is made in 3 standard sizes for the following soft shaft sizes:
1-1/2", 1-3/8", and 1-1/4". The new design for the CB-2000 adds a ridge
around the outside of the sleeve that allows the KSD-G2 to snap into the
tube of the CB-2000 but it fits just a bit looser in the CB-3000 and Curve so as
not to split the cage apart.
All men are made a bit different. Because of the physical makeup of some men, they have found that it is possible to pull out
of the CB-2000, CB-3000, or The Curve, regardless of the configuration of rings and spacers that they use. In order to assist
the man in his desire to stay chaste for his Keyholder, and to give the Keyholder the peace of mind that she deserves, Kept
For Her designed and offers the KSD-G2.
Any man in chastity comes to points of frustration where he will do anything to get out of his CB. The KSD-G2 will aid in
preventing the man from pulling out of the tube and masturbating.
How the KSD-G2 Works
The KSD-G2 fits onto the locking pin and goes partway into the tube, while a part of it is on the outside of the tube. The
KSD-G2 works by adding constriction and friction to the male shaft, thus making attempts at pulling out difficult, if not
impossible. The inside diameter of the KSD-G2 is considerably smaller than the shaft size it was ordered for (see chart
on Measuring page). If indeed you are able to pull out, you will not get back in without your Keyholder finding out. You
will be in big trouble!!
The KSD-G2 will not cause fluid backup (unless you specify the
wrong size and that can be easily corrected!). Also, the KSD-G2
will not cause pain during arousals. It is very comfortable to wear
and to stay hygienically clean while locked up for long periods of
time.
The KSD-G2 is made out of UHMW plastic, which has the qualities
of being lightweight, resistant to any oils or lotions, and easy to
modify if necessary. Each KSD-G2 is manufactured by plastic
injection molding. This process assures you of consistent quality and
exacting tolerances from one unit to the next.
What is the difference between the KSD-G2 for the CB-2000 and
the one for the CB-3000/Curve? The KSD-G2 fits 3/8" into the
chastity tube of the 2000/3000/Curve. The opening of the CB-3000
and The Curve is the same so the same KSD-G2 fits both. The opening of the CB-2000 is larger. So a different KSD-G2 had
to be designed to fit snugly into the CB-2000. The KSD-G2 snaps into the CB-2000 tube but has just a bit looser fit in the tube
of the 3000 and Curve so that it does not split the cage apart.
| Go to MEASURING for a chart comparing the different sized KSD-G2's and their inside diameters for each soft shaft size. |
Patent Pending